Technical News
Find what you need fast and easily
January 2024
1/23/2024
- Upper central seal assembly has been added
1/23/2024
- The designs of the below frame tracks have been corrected
1/23/2024
- Glazing bridge for fixed 290-19-620-00 has been added ont 39 & 43 typologies "One sash doors with fixed panels - inwards opening hidden sash"
December 2023
12/13/2023
- Diagram for the max dimensions for given wind pressure for the profiles M4548+M4577+M4548 has been corrected
12/13/2023
- General redesign of the catalogue
- Pressure and drain equalization for pressure plate and windows have been added
12/13/2023
- Both the individual profiles (i.e., the bottom side profiles) and their corresponding quads (14x19, 18x19, 22x22) have new codes. The new codes are actually the same as the old ones, with the addition of an "N" at the end, for example, new code 138-185N.
- The bottom side of all of our boxes has been changed and reduced by 4mm to improve the alignment/centering of the shutter.
12/13/2023
- Comment that the specific profiles do not use hinge 360-77-950-XX has been added on profiles S95018, S95016 & S95042
12/13/2023
- Handle machining S11531 & S11532 has been added for optimal understanding
12/13/2023
- Add-on profile for hidden sash S77005 was replaced by S77016.
- Accessory 1607790803 Plastic transom cleat for S77phos has been added on typologies 18 & 35.
12/13/2023
- Add-on profile for hidden sash M19637 was replaced by M19633.
- Μachining for crimp corner cleats for the sash M19722 has been added on page 300.
12/13/2023
- Typology of Door M84FR with M7FR has been added.
- Alternative solution for faster installation.
- Glazing table and indicative bill of materials for external fire rated glazing have been added.
November 2023
11/23/2023
- Typology 6: Sash gasket 250-85-036-01 replaced with 250-85-044-03 and the brush 620-11-500-00.
- Typology 25: Additional width for S85035 has been corrected for 6 pieces to 3 pieces and Additional width for S85026 3 pieces has been added.
- Typology 29: Code of frame has been corrected. The right one is S85024.
- Typology 30: Cuttings for the sash width have been corrected.
11/23/2023
- Sash gasket 2506511000 replaced by 2506511103 for optimal operation.
- Lock adjustment instructions have been added on the chapter of General Milling-Tooling Operations.
- New typology No14 outward opening, 3panels on one side folding door.
11/23/2023
- Crimp corner cleat code 113-13-074-00 13,2X7,8 was replaced by 113-13-070-00 13Χ7mm for the sash P158.
11/23/2023
- Glazing bridge 290-77-002-00 has been replaced wit 290-77-005-00 for optimal operation.
- Threshold cap 15mm code 310-77-114-03 has been added on 4,7,15,17 typologies with low threshold S77774.
- Installation Profiles Chapter has been added.
11/23/2023
- General milling-tooling operations have been updated
October 2023
10/25/2023
- Glazing bridge 290-77-002-00 has been replaced with 290-77-005-00 for optimal operation.
- Dimensions have been corrected in pivot machinings.
- Reversing profile height has been corrected in pivot typology No72 Pivot horizontal axes.
- Reversing profile width has been corrected in pivot typology No73 Pivot vertical axes.
10/25/2023
- Glazing list for fixed glazing has been added (4-40mm)