Technical News
Find what you need fast and easily
March 2022
3/4/2022
- Dimensional Limitations chapter has been updated. The diagrams are calculated in compliance with EN 14024.
February 2022
2/22/2022
- Locking solutions for sliding systems catalogue updated with the addition of the M450 system
2/22/2022
- Typology PLS12 Corner assembly with four sash parallel slide (EXTERIOR CORNER) added on the tech catalogue
- Typology PLS13 Corner assembly with four sash parallel slide (INTERIOR CORNER) added on the tech catalogue
- Typologies sections 86 & 87 that refer to the corner typologies added on the specific chapter
- Cuttings of S579 have been corrected in typology FLS1 Fixed - Lift & Slide Window with the Fixed on the Inside and FLS2 Fixed - Lift & Slide Window with Fixed Outside
2/22/2022
- Drainage adaptor code 311-63-163-03 replaced by 311-63-163-04 in all catalogue
- Accessories chapter was updated
2/22/2022
- Flyscreen frame track Μ63145 machining detail added on page 21
- Flyscreen Handle 610-00-701-XX milling added on page 24
2/22/2022
- New typology OUTWARD OPENING, 2+2, 4-PANELS FOLDING DOOR was added on the chapter of sections No 22
- Now, even typologies are activated. All available typologies were updated. 250-85-110-02 Single top gasket and 310-85-450-00 Set of flanges for even typologies were added on the accessories chapter
2/22/2022
- S67032, S67034 & S67036 profiles added on the milling tooling operations of locking (pages 98 & 99)
2/4/2022
- T-cleat inside code 160-11-211-91 has been replaced by 160-11-211-00 in the entire technical catalogue
2/4/2022
- Top central seal 2400450200 replaced by 2400450000 in typology PLS5 (Three Sash Parallel Lift and Slide 45 Degrees Cut Right Opening Window), for optimal operation and long lasting sealing
2/4/2022
- Quantities for the Brush weatherstripping pile trifin code 620-69-306-03 6mm and for the Brush weatherstripping pile code 620-69-106-03 6mm were corrected on all technical catalogue
2/4/2022
- Frame connector for 90 degrees corner typology code 145-11-356-00 added on the accessories chapter.
- Furthermore, the machining for the profile is added in the General Milling-Tooling Operations chapter page 261.
2/4/2022
- Glazing list with bead S540 updated. By using outer gasket 200-06-861-01, 44mm glazing with 3mm inner gasket 200-08-003-01 can be installed. Likewise, 45mm glazing with 2mm inner gasket 200-08-002-01 is also possible
2/4/2022
- Reversed vulcanized corner code 255-77-148-03 added on typologies 38 & 39 (pivot) and on the accessories chapter
- Vulcanized corner for central gasket 210-77-222-03 code 255-77-222-03 added on the accessories chapter
- Brush Pile 20mm 620-11-600-00 replaced by Brush Pile 16mm 620-29-163-03 for optimal operation
2/4/2022
- Moment of interia Ix updated in all thermally broken profiles. The values are now dependent on the length of the profile (<1,5 <2,0 <2,5 <3,0 <3,5 >3,5) because Ιx is calculated in compliance with EN 14024
- Additional profile S67482 has been replaced by S77482
January 2022
1/18/2022
- Big perforation was corrected for the slat 303030 on page 163
- Slats 303019 and 303023 were added to the Extruded Slats chapter
1/18/2022
- Dimensions were corrected for profile S77976
- Glazing bridge code 290-77-936-00 added on the accessories chapter
- The glazing bridges installation is documented on page 285
1/18/2022
- Additional profile added S60057 on profiles chapter
- Glazing bridge code 290-67-936-00 added on the accessories chapter
- The glazing bridges installation is documented on page 340
1/18/2022
- Quantity of top central (2400450200) seal corrected on typologies pls6 & pls7 (2 pcs)
- Cuttings of interlock pvc 6604546003 corrected on typology ps3 (Η-153)
- Outer gasket corrected on glazing list for sashes Μ4542 and M4544 (2000686001 the correct)
1/18/2022
- Add-on profile S67151 was added on the profiles chapter and on page 25 of the typologies section chapter.
- We can choose this alternative solution (option A) of frame and sash in order to cancel the visible outer gasket (option B)